Stress Corrosion Cracking Behavior of Stainless Steel 304 in the Sulfuric Acid Environment Due to Prestrain

Authors

Mohammad Badaruddin, Jurusan Teknik Mesin, Fakultas Teknik, Universitas Lampung, Bandar Lampung 35145, IndonesiaFollow
Ahmad Suudi, Jurusan Teknik Mesin, Fakultas Teknik, Universitas Lampung, Bandar Lampung 35145, Indonesia
Arinal Hamni, Jurusan Teknik Mesin, Fakultas Teknik, Universitas Lampung, Bandar Lampung 35145, Indonesia

Abstract

Stress Corrosion Cracking Behavior of Stainless Steel 304 in the Sulfuric Acid Environment Due to Prestrain. The aim of research is to investigate the effect of prestrain on the stress corossion cracking behavior of AISI 304 stainless steel in the sulfuric acid of 10% concentration under the static cantilever loading according to ASTM E-1681 standart. The specimen of 304 Stainless steel was strain up over the yield strength until reaching the uniform strain of 5% and 10% using servopulser UTM 9506 under the displacement control of 0,3 mm/sec. The results of test show that the prestrain of 5% specimen is faster failure than both of the prestrain of 10% and unprestrain specimen. It was caused by both of the decrease of ductility and the short incubation period. The change of deflection could be only recorded under the loading 20% of yield strength. Intergranular crack was the prestrain of 10% specimen under the static loading of 616 MPa. Whereas, for the prestrain of 10% specimen transgranular crack was found under the static loading of 554,4 MPa. The prestrain of 5% specimen was mixed crack under the static loading of 369.6 MPa. Higher dislocation density on the layer surface due to plastic deformation with increasing the percentage of pre-strain, so more difficult hydrogen diffused into the crack tip. Consequently, The incubation period can be prolonged.

Bahasa Abstract

Tujuan penelitian ini adalah untuk mengetahui pengaruh prestrain terhadap perilaku korosi retak tegang stainless steel AISI 304 dalam larutan H2SO4 konsentrasi 10% dengan pembebanan kantilever statis (ASTM E-1681). Prestrain dilakukan dengan meregangkan spesimen hingga mencapai regangan merata 5% dan 10% diatas tegangan luluh bahan, menggunakan servopulser UTM 9506 dengan kontrol kecepatan 0,3 mm/sec. Hasil pengujian menunjukan bahwa spesimen dengan 5% prestrain lebih cepat mengalami kegagalan daripada spesimen 10% prestrain dan tanpa prestrain. Hal ini disebabkan menurunnya keuletan dan periode inkubasi yang singkat. Perubahan defleksi hanya dapat diamati pada pembebanan 20% tegangan luluh bahan. Retak intergranular ditemukan pada spesimen 10% prestrain pada pembebanan statis 616 MPa. Sedangkan pada specimen 10% prestrain ditemukan retak transgranular pada pembebanan statis 554,4 MPa. Retak kombinasi ditemukan pada specimen 5% prestrain pada pembebanan statis 369,6 MPa. Semakin tinggi densitas dislokasi pada lapisan permukaan akibat deformasi plastis, semakin sulit difusi hidrogen pada ujung retak. Konsekuensinya, periode inkubasi dapat diperlama..

References

1. Zhang, Y.L. Chiang, M.A. Streicher, NACE International 39 (1998) 114-119
2. Sivaprasad, S, Tarafder, S, Ranganath, V.R, Das,S.K, Ray, K.K, J. Met.Mat.Trans, 33A(2001)3731-3739.
3. Badaruddin M, dan Sugiyanto, J. Tek. Mesin Univ.Kristen Petra Surabaya (2005) 11-14.
4. A. Cigada, B. Mazza, P. Pedeferri, G. Salvago, D.Sinigaglia and G. Zanini, J. Corrosion Science,22/6 (1982) 559-578.
5. Kirk, D, and P.E. Render, Int. Con. Of Shot Peening 7th , Warsaw-Poland (2001) 167-176.
6. Yunovich, Josephic , NACE international 1998.
7. Tateishi, T, Hanjin, T, J. Struct. Mech. Earthquake Eng, JSCE 59, I-43 (2003) 243-261.
8. D. J., Frizt, Ronald. J. Gerlock, J. Desalination, 13/5 (2001) 93-97.
9. Zdravko P, Masao Toyoda, Int. Conf. 39th, Exp. Stress Analysis, Tabor-Czech Republic (2001)46-52.
10. Sakata, Kawasaki Steel Tech. Report, 48 (2003)
11. Qiao, L, Y. L. Huang, J.Master Science, 25 (1998) 47-51.
12. ASTM E-1681, ASTM International USA (2004) 1-15.
13. Watanabe,Y., and Hasegawa, N., Int. Con. Of Shot Peening7th, Warsaw-Poland (2001) 841-846.
14. Kritzler, J. Int. Con. Of Shot Peening 7th, Warsaw-Poland (2001) 142-147.

Recommended Citation

Badaruddin, Mohammad; Suudi, Ahmad; and Hamni, Arinal (2006) "Stress Corrosion Cracking Behavior of Stainless Steel 304 in the Sulfuric Acid Environment Due to Prestrain," Makara Journal of Technology: Vol. 10: Iss. 2, Article 3.
DOI: 10.7454/mst.v10i2.1020
Available at: https://scholarhub.ui.ac.id/mjt/vol10/iss2/3